This SMLC make hot melt Adhesive applicator machine is a sophisticated easy to use machine. The system is made keeping in mind insulation and adequate heating. It comprises of a coated container PFT/ Non PFT (1 to 20 litters),connected to the dispensing system which is heated and isolated. It is further connected to automatic dispensing gun for seamless and hassle-free application.
It comes in two variants to meet the needs of the user.
- Volumetric Hot melt adhesive applicator
The system comprises of a Pressure pot (1 to 20 litters), a heated jacket for pressure pot along with a heated base plate, heated hose, and an automatic dispensing gun for seamless and hassle application.
2. Hot melt adhesive applicator with gear Pump.
The system comprises of a Pressure pot (1 to 20 litters), a heated jacket for pressure pot along with a heated base plate, heated hose, and an automatic dispensing gun for seamless and hassle application.
For precise application a variant is developed by SMLC, which allows the user to dispense material with utmost precision. This variant come with an attached gear pump which makes this possible.
(capacity 2 to 20 kg)
FEATURES –
- High flow rate pumps and guns
- Priming piston (shovel) type suction for high viscosity fluids
- Superior quality spares to reduce maintenance cost
- Auto shut off for pumps
- Facility for twin pall switchover system
- Drum capacity 20 lit and 200
- Custom built system for more drum capacity with special features
- Separately heating system with PLC base control
- Temperatures of individual heated parts can be visible on HMI Display with special security features
- Hydraulic Stroke count possible to check per day material consumption (optional)
- Air consumption monitoring (optional)
- These are equipped with medium duty or heavy-duty range of pumps and are suitable for semi-solid and pasty materials
Specifications –
Machine size (LxWxH) |
600 x600x700 |
Machine weight |
70 kg |
Supply Voltage |
Single phase, 32 amp ,230 v, 50 Hz |
Dry compressor Air |
0-10 bar max air pressure |
Dispensing gun block heater |
200 watts |
heater jacket |
3kw |
Base heater |
500 watts |
Timer controller |
1 millisecond to 10 minutes manual set |
Value output |
Shot size approx. 0.5 ml to 10 ml |
Hot melt glue heating time |
30 min to 2 hrs approx. |
Wetted parts |
SS 304, brass, aluminum, Viton |
Glue pressure pot air inlet pressure |
6 bar Max. |
Max operating Temperature |
200 deg. Celsius |
The System will be consisting of the following items
- Pressure feed tank 1 litter to 20 litter (as per required)
- Heating jacket and base heater attached with tank
- Automatic dispensing gun
- Dispensing gun block heater
- Foot pedal operated switch
- Electropneumatic control panel
- Dispensing Flow rate: customized
- Ratio variation: customized as per application
- Machine encloser
Utilities required for Machine: Power 4-6 KW, Air consumption: 100 LPM at 5-6 bar
Operations of the Machine –
- Install machine in clean and dry area on the table away from fan air (Breeze)
- Clean the machine, controller, pressure pot completely
- Connect air supply to the machine (dry air) 0 – 10 bars
- Connect the supply voltage to the machine with proper earthing
- Check the operation ON/OFF of the glue dispensing valve providing air 0-10 bar, on timer controller
- Check the heating of pressure pot, dispensing gun block by individual turning on/off power
- If dispensing valve operation and heating system is correct then switch off the power and fill the glue material in the pot.
- Closely tight the lid of pressure pot
- Switch on the pressure supply and set the temp. as per required for the glue melting
- Again, check the air release valve by pulling the ring for safety working.
- Wait for set the temperature point it will take some time when the material melts then press paddle switch to operate dispensing gun.
As per hot melt glue timer take out material from the gun.